Completed Screwdriver Rack

Here is a really handy DIY screwdriver rack. It will keep your screwdrivers organized so you don’t have to rummage through the bottom of your toolbox to find the right one. This screws directly to the wall or you can hang it on your pegboard. It only takes a few tools and some really inexpensive lumber.

And follow my Video to see how it is done.

Tools and Materials

The tools that you’re going to need for this screwdriver rack are minimal. You could do this one all with hand tools, but I suggest a few power tools. You will of course need a tape measure, a combination square, a spade bit set, a drill motor, and a saw.

And for materials you will need a 18” – 20” long piece of 2 x 4 cut down to 2” wide. and if you are attachind ti to t pegboard you will need 1-1/2″ (~40mm) “L” hooks

Materials

Layout

Layout starts with using your combination square to strike a line down the center at 1 inch. Next, follow the dimensions on the sketch below beginning at 1-1/4” from the end. The first three holes on the right are 4 Phillips screwdrivers #1, #2, and #3. The next series of holes are for flat screwdrivers, three each of 1/8”, 1/4”, 5/16” widths. If you don’t have all those screwdrivers you can just not mark the holes or put them in for future tools.

Layout Screwdriver holes

Please note that the design is for my screwdrivers. You may have more or less and they may be larger or smaller. Be sure you check dimensions before you start drilling. You may even have to drill a few test holes to make sure things are going correctly. I will say the last and largest hole on the left is probably not needed for anything you are doing. That is for a special screwdriver that I used to used with my grandfather when we worked on the old Ford 9N tractor. I’m including that because it has a lot of sentimental value even though it’s really beat up.

Drawing of Screwdriver Rack

Drilling

But you have all the hole centers marked you will need to select and chuck a spade bit of the appropriate size into your drill motor. The correct size is the larger of the two that are noted. So for the 1st hole that will be 3/4 inch. What you’re actually doing here is drilling a counterbore. Drilling the larger hole first makes it far easier to center the smaller through hole. I suggest that you drill all the counter bores first then come back and drill all the through holes. Drill the counter bore holes 3/4 inch deep.

With all the counter bores complete move on to drilling the through holes. Be sure you have some kind of backer board you can drill into. Otherwise, you may drill into your bench. The backer also helps to prevent blowout on the backside. You can eliminate blowout by drilling almost all the way through turning the piece over and finish drilling from the bottom up. The point of the spade bit will create a center that you can use.

Drilling Screwdriver Holes

Cutting the Screwdriver Rack to Length

Next you’re going to want to cut the screwdriver rack to the appropriate length. Measure about 1 inch from the edge of the final left-hand hole and cut off the excess wood.

Now be sure that you also mark and drill the two mounting holes on the face if you are going to mount it directly to the wall.

Sanding

Depending on how rustic you want this now is the time to sand all the surfaces. If you’re using a piece of construction grade 2 x 4 it will probably be pretty rough so you should start with 60 or 80 grit sandpaper and then move to 150 and finally 220 grit sandpaper. Be sure to round off any sharp corners or edges.

Sanding Screwdriver Rack

Finishing

You can finish the screwdriver rack in any manner you choose. Whether bright yellow with black accents, a warm orange lacquer, or a simple coat of wax all will be beautiful in the end. I finished mine two coats of boiled linseed oil mostly because that’s what I have easy to hand. The pine sucked up the first coat very quickly. But the second coat took a day or two for it to fully cure.

Applying Finish to Screwdriver Rack

Final Assembly

At the last minute I decided to just hang it on my pegboard. If you choose this route hold it up to the pegboard and mark the location of the hole.

NOTE: Be sure that the hooks don’t interfere or intersect with the holes for the screwdrivers.

Measure down 3/8” along the centerline of the pegboard hole. Next drill a 1/8” hole 1” deep. Screw in the “L” hook to about the thickness of your pegboard. Use an Awl to mark the drill point. It will keep the drill from walking.

Oops! You can see I miss-marked the first time. I caught the mistake before I actually started drilling. Measure Twice, Cut Once!!

Final Assembly

Closing and congratulations

Well if you made this project you’re done the last step is to screw it to the wall and load it with your screwdrivers. I actually hung mine on the pegboard but you can screw it directly to the wall.

Finished Screwdriver Rack

Hope you got something out of this and if you did, do me a favor, hit like and subscribe. I’d appreciate that a lot.

Thanks for reading and until next time Good Making!

Bill

Visit my Etsy Store at   www.etsy.com/shop/30MinuteWoodshop 

Facebook   https://www.facebook.com/30MinuteWoodshop 

Links to my Videos and Blogs

Create Your Own Dice Vault     https://30minutewoodshop.com/?p=1226

DIY Whiskey and Cigar Butler     https://30minutewoodshop.com/?p=550

Farmhouse Key Rack     https://youtu.be/I65FGq4dKYY

Create Your Own Lazy Susan     https://30minutewoodshop.com/?p=491 

Tools and Materials you may need

1.5 “L” Hooks https://amzn.to/3QWLla0

DEWALT Drill and Driver Combo      https://amzn.to/42yybmy 

DEWALT Router Plunge Base Kit      https://amzn.to/3LKkJEK

SPEEDBOR Spade Bit Set      https://amzn.to/44pusrw

Ridgid Oscillating Sander    https://amzn.to/45C3rTK

Starrett Combination Square      https://amzn.to/3XpbrDN

DeWalt Tape Measure https://amzn.to/3OYpqfV

WoodRiver Low Angle Block Plane           https://amzn.to/3pkNvos

BOSCH Compound Miter Saw       https://amzn.to/421A1vl

Minwax Fast Drying Polyurethane     https://amzn.to/3V5h0pO

PPE Gear

3M N95 PPE Mask     https://amzn.to/3x4NGEu

ISOtunes Bluetooth Earmuffs     https://amzn.to/3lpj1iA